Re: Testpiloter till DLINK DNS-323 sökes / Testers needed for DLINK Dns-323
Hej!
Jag håller på att försöka sätta upp en DNS-320 med Thermiq och en Diplomat Optimum G2. Nån som försökt sig på detta än?
Jag har i vilket fall stegat mig igenom installations-scripten för DNS-323 och försökt gissa mig till varför saker går fel. Än så länge har jag hittat följande:
1) wiki.dns323.info är nere men dns323.kood.org fungerar till vidare.
fun_plug:
2) Alla instanser av /mnt/HD_a2 behöver bytas ut mot /mnt/HD/HD_a2
3) En ny version av store-passwd.sh behövs
Jag håller nu på att strula med thermiq-installationsscriptet. Har f.n. fastnat på
a) i slutet av installationsscriptet skriver den ut
removing ThermIQ cron job
stty: can’t open ‘/dev/ttyUSB0’: No such file or directory
Adding ThermIQ to cron jobs
Done
Om jag bootar om DNS:en så klagar den på (i ffp.log):
**** fun_plug script for DNS-320 ****
**** (modified from fun_plug script for DNS-323 (2008-08-11 tp@fonz.de)) ****
Mon Jan 23 14:52:59 CET 2012
ln -snf /mnt/HD/HD_a2/ffp /ffp
* Running /ffp/etc/fun_plug.init …
* Running /ffp/etc/fun_plug.local …
cp: cannot stat ‘/ffp/thermiq/pkg_dns323/usb.agent’: No such file or directory
chown: /etc/hotplug/usb.agent: No such file or directory
chmod: /etc/hotplug/usb.agent: No such file or directory
insmod: cannot insert ‘/lib/modules/2.6.12.6-arm1/usb-storage.ko’: invalid modul
e format
insmod: cannot insert ‘/lib/modules/2.6.12.6-arm1/usbserial.ko’: invalid module
format
stty: can’t open ‘/dev/ttyUSB0’: No such device or address
* Running /ffp/etc/rc …
* /ffp/start/syslogd.sh inactive
* /ffp/start/SERVERS.sh inactive
* /ffp/start/portmap.sh inactive
* /ffp/start/unfsd.sh inactive
* /ffp/start/nfsd.sh inactive
* /ffp/start/ntpd.sh …
Starting /ffp/bin/ntpd -g -f /tmp/ntp.drift
* /ffp/start/LOGIN.sh inactive
* /ffp/start/thermiq.sh …
stty: can’t open ‘/dev/ttyUSB0’: No such device or address
Adding ThermIQ to cron jobs
* /ffp/start/telnetd.sh inactive
* /ffp/start/sshd.sh …
Starting /ffp/sbin/sshd
* /ffp/start/rsyncd.sh inactive
* /ffp/start/mediatomb.sh inactive
* /ffp/start/kickwebs.sh inactive
* /ffp/start/lighttpd.sh …
WARNING: lighttpd: Already running
* /ffp/start/inetd.sh inactive
* OK
% uname -a
Linux eddie 2.6.22.18 #23 Wed May 25 15:48:30 CST 2011 armv5tejl unknown
% dmesg
Linux version 2.6.22.18 (jack@swtest4) (gcc version 4.2.1) #23 Wed May 25 15:48:30 CST 2011
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
DMA zone: 256 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 32512 pages, LIFO batch:7
Normal zone: 0 pages used for memmap
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80×30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 123776KB available (4148K code, 252K data, 124K init)
Calibrating delay loop… 791.34 BogoMIPS (lpj=3956736)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU Interface
SDRAM_CS0 ….base 00000000, size 128MB
SDRAM_CS1 ….disable
SDRAM_CS2 ….disable
SDRAM_CS3 ….disable
PEX0_MEM ….base e8000000, size 128MB
PEX0_IO ….base f2000000, size 1MB
INTER_REGS ….base f1000000, size 1MB
NFLASH_CS ….base fa000000, size 2MB
SPI_CS ….base f4000000, size 16MB
BOOT_ROM_CS ….no such
DEV_BOOTCS ….no such
CRYPT_ENG ….base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_4.3.4_patch30)– DB-88F6281A-BP Soc: 88F6281 A1 LE
Detected Tclk 166666667 and SysClk 200000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c05c3600
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: kw_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs…it isn’t (no cpio magic); looks like an initrd
Freeing initrd memory: 1529K
cpufreq: Init kirkwood cpufreq driver
cpufreq: High frequency: 800000KHz – Low frequency: 200000KHz
cpufreq: Setting CPU Frequency to 800000 KHz
cpufreq: Setting PowerSaveState to off
XOR registered 1 NET_DMA over 4 channels
XOR 2nd invalidate WA enabled
cesadev_init(c00119d8)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.
SGI XFS with large block numbers, no debug enabled
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.7 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: module loaded
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support – ETH_DEF_RXQ=0
o Single TX Queue support – ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o LRO support supported
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o SKB Reuse supported
o SKB Recycle supported
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o register under egiga0 platform
o egiga0, ifindex = 1, GbE port = 0
Warning: Giga 1 is Powered Off
mvFpRuleDb (c07a9000): 1024 entries, 4096 bytes
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access Seagate ST2000DL003-9VT1 CC32 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access Seagate ST2000DL003-9VT1 CC32 PQ: 0 ANSI: 5
scsi 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 0
NFTL driver: nftlcore.c $Revision: 1.1.1.1 $, nftlmount.c $Revision: 1.1.1.1 $
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 68 at 0x00880000
Bad eraseblock 795 at 0x06360000
Using static partition definition
Creating 6 MTD partitions on “nand_mtd”:
0x00000000-0x00100000 : “u-boot”
0x00100000-0x00600000 : “uImage”
0x00600000-0x00b00000 : “ramdisk”
0x00b00000-0x07100000 : “image”
0x07100000-0x07b00000 : “mini firmware”
0x07b00000-0x08000000 : “config”
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: 2006 August 04 USB 1.1 ‘Open’ Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
cpufreq: Setting CPU Frequency to 800000 KHz
cpufreq: Setting PowerSaveState to off
usb 1-1: new full speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun …
md: … autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 124K
sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 10 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 3907029168 512-byte hardware sectors (2000399 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 10 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 23 00 10 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 23 00 10 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1 sdb2 sdb4
sd 1:0:0:0: [sdb] Attached SCSI disk
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
egiga0: mac address changed
egiga0: link up, full duplex, speed 100 Mbps
egiga0: started
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb4, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Initializing USB Mass Storage driver…
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: md1 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
EXT3 (no)user_xattr options not supported
kjournald starting. Commit interval 5 seconds
EXT3 FS on md1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 530040k swap on /dev/md0. Priority:-1 extents:1 across:530040k
scsi 2:0:0:0: Direct-Access ThermIQ Mass Storage 0001 PQ: 0 ANSI: 4
usb-storage: device scan complete
NTFS driver 2.1.28 [Flags: R/O MODULE].
usb_storage: version magic ‘2.6.12.6-arm1 ARMv5 gcc-3.3’ should be ‘2.6.22.18 mod_unload ARMv5 ‘
usbserial: version magic ‘2.6.12.6-arm1 ARMv5 gcc-3.3’ should be ‘2.6.22.18 mod_unload ARMv5 ‘
Nån som har nån ledtråd på hur jag ska gå vidare? dmesg föreslår att jag ska leta en usb_storage.ko och usbserial.ko som är kompatible med min kernel. Var? Nånting annat?
Jag lovar att posta en fullständig uppdatering när jag får min DNS-320 att fungera.
Mvh,
/Niclas
