Anders a
Forum Replies Created
-
AuthorPosts
-
2023/10/22 at 22:02 in reply to: Suggestions and recommendations for energy saving and automations #8427
Anders a
Keymaster1) I’m only using the EVU function as that is easiest
2) I run it based on hours and terminate an ongoing run. It could make sense to let it complete a run before terminating.
The amount of hours differs depending on your house and hotwater consumption. If you set it to low you will not be able to maintain the indoor temperature or might get to much variation in room-temperature. Give it to many and you would save less.
The whole idea is to push consumption to low-cost hours and sacriface by a larger variation in temperature. Actual variation depends on your house’s ability to store energy, kind of like a capacitor smoothing out a voltage variation.
3) I would try to keep all floors active as much as possible while the heatpump is running.
Anders a
KeymasterHej Magnus,
Det är en inställning på min sida som avgör om du får USB eller MQTT pollern.Du är nu uppdaterad så gå till installation -> Main database och se till att ThermIQ_MQTT är vald och updatera db:n om nödvändigt.
2023/10/11 at 19:58 in reply to: FLowline pump and brine pump speed not updating with thermiq-usb #8418Anders a
KeymasterI would check if the right type of heatpump is selected in Settings -> Main Thermia
Anders a
Keymasterjag har inte testat mot pelletsbrännaren. Det borde vara en helt annan addresskarta så jag har svårt att tro att det skulle gå.
-
This reply was modified 3 years, 2 months ago by
Anders a.
Anders a
Keymastersånt som händer 🙂
Anders a
KeymasterHej,
Fw 1.xx går tyvärr inte längre att uppgradera via OTA.Det du kan göra är att köpa uppgraderingen till room2 och skicka den till mig. Då kommer du automatiskt få fw 2.xx.
Anders a
KeymasterSer ut som att du har problem med att komma ut på nätet, thermiq.net ser ut att må bra. Är du säker på att du kommer ut på nätet från PIn?
Anders a
KeymasterHej,
Ser ut som att du inte har rätt version av oset, du ska bullseye för att allt ska funkaAnders a
KeymasterHi,
Please Contact me directly on mail and I’ll help you troubleshoot…
/&&Anders a
KeymasterThermiq is connected to the indoor unit
Anders a
KeymasterThermiq is connected to the indoor unit
Anders a
KeymasterHi,
I depends on which indoor unit you have,
I think that the Thermia ITEC is the product name for outdoor unit to which you can connect several different inddor units. Some of these are compatible with ThermIQ, some are not.If compatible you will be able to run the heatpump in “heastpump only” or “electric heater only” mode (as well as auto). You can not directly turn on or off the electric heater.
Anders a
KeymasterHi Niklas,
That control board is unfortunately not supported by ThermIQ,Rgds
/&&Anders a
KeymasterThe EXT connector is on the main compute board of the heatpump. Look for the men “Compatible heatpumps” for some pictures.
The ThermIQ-board itself maintain the settings given to it by your home automation system and does not take any decisions by itself. If your automation system hangs ThermIQ will maintain last settings, but a power outtake will reset the board to a non-blocked EVU state
Anders a
KeymasterIf I understand it correctly, the ITEC in itself is the outdoor part of the pump and there are different indoor units that can be attached.
If you can find an “EXT” connector on the mainboard it will most likely work. To be sure you can send me a picture of the main-board as well.
/&&
-
This reply was modified 3 years, 2 months ago by
-
AuthorPosts


