Anders a
Forumsvar skapade
-
FörfattareInlägg
-
Anders a
KeymasterHej Fred,
ThermmIQ har ingen egen klocka utan använder raspberryns inbyggda. Den synkar normalt över nätet mot något atomur./&&
Anders a
KeymasterHi,
The old version have been discontinued for more than two years now. I recommend you to upgrade to the latest as you get a much improved user-interface as well as some new functionality.The old version does not run on raspbian-Jessie but requires the older Wheezi
Anders a
KeymasterHej,
Det är riskfritt att återskapa userdb med create userdb. All logg-data ligger i thermiq-databasen.Anders a
KeymasterThis is likely due to glitches in logging. Please check that you have latest firmware on the ThermIQ interface and also have latest sw on your server.
Anders a
KeymasterJa det är för att ge mer skärmyta till graferna
Anders a
KeymasterJag får försöka göra något. Tyckte det var en cool feature men det är nog den vanligaste frågan jag får på mail…
Anders a
KeymasterVet faktiskt inte varför det blir så. Tror det kan vara något med cookies som timar ut. I nya thermiq2 använder jag ett färdigt ”paket” för inloggningen så jag Kan inte styra alla bitar.
Anders a
KeymasterDet är avsiktligt för attgemer skärmtak till graderna. Prova att touchdown gröna linjen så kommer den att åka ned.
Anders a
KeymasterOk,
You have USB-Com working. You have latest version. And no SD-Card. That’s good.L2 blinking means that ThermIQ sees communication between heatpump and Thermia Online. That’s also good but still you get a timeout when trying to talk with the pump.
Let’s take the support over mail to speed things up.
Rgds
/AndersAnders a
KeymasterFirst thing is to remove the SD-Card from ThermIQ. It’s no longer used.
Second thing is to make sure you have the latest Thermiq-firmware. Check the current FW-version under ”Settings/Main”. Current version is ThermIQ2 v4.35 0096. Upgrade if necessary
Third thing to try is to login to your Raspberry and type
sudo picocom /dev/ttyUSB0This will start a terminal towards the ThermIQ card where you can test it with direct communication.
Type
atiTo get firmware verion and confirm that USB-com is working
Type
atr0010To confirm communication with the heatpump. If the later fails please check your connections with the heatpump, make sure that the ThermIQ card is in between the main-controller and any extension boards.
Also do a restart of the heatpump.Anders a
KeymasterI ThermIQ2 så kan man ju spara upp databasen på DropBox. Om man sedan tar ned den till sin PC/Mac och öppnar med en sqlite-hanterare så kan man göra nästan vad som helst. Pröva tex sqlitebrowser.org
2015/11/24 kl. 23:50 som svar på: ./setup_script: 157: ./setup_script: Syntax error: newline unexpected #6706Anders a
KeymasterI’m sorry for creating problems for new installations on Raspberry but it seems I brook the installation script in several places when trying to update it for Raspbian Jessie. I think it is finally under control now from version 455
2015/11/24 kl. 11:28 som svar på: ./setup_script: 157: ./setup_script: Syntax error: newline unexpected #6703Anders a
KeymasterDet kan vara nödvändigt att skriva
sudo rm /etc/setup_script
för att ta bort det gamla scriptet innan man laddar ner det nya med sudo wget……2015/11/23 kl. 22:26 som svar på: ./setup_script: 157: ./setup_script: Syntax error: newline unexpected #6701Anders a
KeymasterLadda ner scriptet igen och kör.
2015/11/22 kl. 23:46 som svar på: ./setup_script: 157: ./setup_script: Syntax error: newline unexpected #6698Anders a
KeymasterDet är nu fixat tillsamman med lite smidigare setup av Tellstick och experimentel support för Rasbian Jessie
-
FörfattareInlägg


